BERTOCCHI, Enrico
BERTOCCHI, Enrico
Dipartimento di Ingegneria "Enzo Ferrari"
3D-FEM ANALYSIS OF DIFFERENT CONFIGURATION OF FULL-ARCH MANDIBULAR IMPLANT PROSTHESIS. PRELIMINARY REPORTS
2010 Natali, Alfredo; C., Pirondi; Bortolini, Sergio; E., Campioni; Bertocchi, Enrico; Baldini, Andrea; Consolo, Ugo
A Complementarity Formulation of the Tangential Velocity Slip Problem in Lubricant Films
2013 Strozzi, Antonio; Giacopini, Matteo; Bertocchi, Enrico; Daniele, Dini
A complete 3-D description of the elastic behavior of a piston ring and its influence on the tribological behavior of the piston ring-cylinder liner interface
2016 Mastrandrea, LUCA NICOLO'; Giacopini, Matteo; Bertocchi, Enrico; Strozzi, Antonio; Dini, D.
A contribution to the Legendre series solution of the mechanical analysis of cylindrical problems
2012 Strozzi, Antonio; Baldini, Andrea; Giacopini, Matteo; Bertocchi, Enrico; Campioni, Eleonora; Mantovani, Sara
A New Volumetric Parameter for a Comparative Finite-Element Analysis of a Six- or Four-Implant Mandibular Total-Arch Rehabilitation
2016 Natali, Alfredo; Bertocchi, Enrico; Baldini, Andrea; Mulas, Giuseppe Antonio; Martinolli, Matteo; Bortolini, Sergio
A Note on the Legendre Series Solution of the Laplace Equation for Cylindrical Problems
2015 Strozzi, Antonio; Bertocchi, Enrico
A paradox in curved beams
2019 Strozzi, Antonio; Bertocchi, Enrico; Mantovani, Sara
A repertoire of failures in connecting rods for internal combustion engines, and indications on traditional and advanced design methods
2016 Strozzi, Antonio; Baldini, Andrea; Giacopini, Matteo; Bertocchi, Enrico; Mantovani, Sara
A repertoire of failures in gudgeon pins for internal combustion engines, and a critical assessment of the design formulae
2018 Strozzi, A.; Baldini, A.; Giacopini, M.; Bertocchi, E.; Mantovani, S.
A Sensitivity-Based Approach to Improve Efficiency of Automotive Chassis Architecture
2013 Valgimigli, Alessandro; Bertocchi, Enrico; Lazzarini, Alberto; D'Agostino, Luca; Splendi, Luca
A simple method of analysis of partial slip in shrink-fitted shafts under torsion
2018 Bertocchi, E.; Mantovani, S.; Ciavarella, Michele
Achievement of a uniform contact pressure in a shaft–hub press-fit
2013 Strozzi, Antonio; Baldini, Andrea; Giacopini, Matteo; Bertocchi, Enrico; Bertocchi, Luca
Advanced high performance vehicle frame design by means of topology optimization
2010 Cavazzuti, Marco; A., Merulla; Bertocchi, Enrico; Strozzi, Antonio; M., Pettazzoni
Aluminum structures in automotive: Experimental and numerical investigation for advanced crashworthiness
2015 Miscia, Giuseppe; Rotondella, Vincenzo; Baldini, Andrea; Bertocchi, Enrico; D'Agostino, Luca
ANALISI PRELIMINARE DELL’INFLUENZA DI SUPERFICI TEXTURIZZATE SUL COMPORTAMENTO DEL FILM FLUIDO IN PROTESI D’ANCA ATTRAVERSO UN ALGORITMO COMPLEMENTARE CON CONSERVAZIONE DELLA MASSA
2014 Mulas, Giuseppe Antonio; Giacopini, Matteo; Strozzi, Antonio; Baldini, Andrea; Bertocchi, Enrico
ANALYSIS OF A SEGMENTED LOCKING RING FOR SHELL - BOTTOM CONNECTION IN PRESSURE VESSELS
2017 Strozzi, Antonio; Bertocchi, Enrico; Mantovani, Sara
Analysis of a segmented locking ring for shell-bottom connection in pressure vessels
2018 Strozzi, A.; Bertocchi, E.; Mantovani, S.
Analytical evaluation of the peak contact pressure in a rectangular elastomeric seal with rounded edges
2015 Baldini, Andrea; Bertocchi, Enrico; Giacopini, Matteo; Mantovani, Sara; Strozzi, Antonio
Analytical evaluation of the peak contact pressure in a rectangular elastomeric seal with rounded edges
2016 Strozzi, Antonio; Bertocchi, Enrico; Mantovani, Sara; Giacopini, Matteo; Baldini, Andrea
Appreciable cross section reduction upon moderate intrados bending stress increase in curved beams
2018 Strozzi, A.; Bertocchi, E.; Mantovani, S.